Gunsmith Punches USA & Canada







HOME PAGE PRODUCTS



Gunsmith Punches USA & Canada


Gunsmith Punches USA & Canada




Brownells Hole Center Punches #8 Hole Center Punch USA & Canada
Brownells Hole Center Punches #8 Hole Center Punch USA & Canada

USD 8.99 (Indicative price - actual current price possibly lower)
3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base. Drill and tap first hole. Re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Manufacturer: brownells specs: 2- " (7.0cm) long. " (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080732008-080732006-11370.
More....

Brownells Roll Pin Punches Kit Type 230-112-105 USA & Canada
Brownells Roll Pin Punches Kit Type 230-112-105 USA & Canada

USD 26.99 (Indicative price - actual current price possibly lower)
The only way to properly install or remove roll pins without damage to either the pin or the surrounding metal. A small raised projection in the face of the punch automatically centers the punch and prevents the roll pin from collapsing. Manufacturer: brownells specs: #1, 1⁄16" (1.6mm) x 23⁄4" (7cm) l. #2, 5⁄64" (2mm) x 3" (8.2cm) l. #3, 3⁄32" (2.4mm) x 3" (9cm) l. #4, 1⁄8" (3.2mm) x 4" (10.2cm) l. #6, 3⁄16" (4.8mm) x 4" (11.4cm) l. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 230112105-230112105-11370.
More....

Brownells Roll Pin Starter Punches #7 Punch USA & Canada
Brownells Roll Pin Starter Punches #7 Punch USA & Canada

USD 6.99 (Indicative price - actual current price possibly lower)
Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Manufacturer: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm). #2, 5/64" (2mm). #3, 3/32" (2.4mm), #4, 1/8" (3.2mm). #5, 5/32" (4mm). #6, 3/16" (4.8mm). 7/32" (5.5mm). #7, 7/32" (5.5mm). High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080000248-080000241-11370.
More....

Brownells Roll Pin Punches #1 Roll Pin Punch USA & Canada
Brownells Roll Pin Punches #1 Roll Pin Punch USA & Canada

USD 8.99 (Indicative price - actual current price possibly lower)
With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Manufacturer: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm). #2, 5/64" (2.0mm). #3, 3/32" (2.4mm). #4, 1/8" (3.2mm). #5, 5/32" (4.0mm). #6, 3/16" (4.8mm). #7, 7/32" (5.5mm). High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 230100001-230100000-11370.
More....

Brownells Cup Tip Punches Model 3 .072" (1.8mm) Diameter/Long Length USA & Canada
Brownells Cup Tip Punches Model 3 .072" (1.8mm) Diameter/Long Length USA & Canada

USD 17.99 (Indicative price - actual current price possibly lower)
Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Manufacturer: brownells specs: punches - steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long. .066" (1.7mm)/long. .072" (1.8mm/long. .040" (1mm)/short. .050" (1.3mm)/short. .050" (1.3mm)/long. 3mm (.118")/long. 3mm (.118")/short. Bench bl. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080620003-080620001-11370.
More....

Brownells Gunsmith Replaceable Pin Punch Set Replacement Pins 2"x.091" USA & Canada
Brownells Gunsmith Replaceable Pin Punch Set Replacement Pins 2"x.091" USA & Canada

USD 14.99 (Indicative price - actual current price possibly lower)
Finally! what we think is the answer to the pin punch headache that has plagued us - and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now - just replace the tip!handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof c.R.S. Steel - tensile strength of over 140,000 psi (min.). Replaceable punch - the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to rc 58-60. Heads are annealed to rc 42-45. They come in two lengths a Manufacturer: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 2 " (6.3cm) long. Replacement pin punch sets include the following pin sizes: 0.039", 0.060", and 0.091" in either 2" or 2 " lengths. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080509691-080507239-11370.
More....

Brownells 1/4" Brass Drift Punch USA & Canada
Brownells 1/4" Brass Drift Punch USA & Canada

USD 4.99 (Indicative price - actual current price possibly lower)
A harder-than-nylon but softer-than-steel punch for drifting fixed sights without damage. Manufacturer: brownells specs: steel handle, replaceable brass tip. 3 " (9.5cm) long. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080920102-080920102-11370.
More....

Geissele Automatics Trigger Fitting Pin USA & Canada
Geissele Automatics Trigger Fitting Pin USA & Canada

USD 14.99 (Indicative price - actual current price possibly lower)
The geissele trigger fitting pin is correctly sized to help with all small pin ar-15/ar-308 hammer and trigger installations. Manufacturer: geissele automatics llc specs: pin o.D. 0.154". High specification gunsmith punches by Geissele, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 100015134-100015134-11370.
More....

Mayhew Steel Single Pin Punches 5/32" (4.0mm) 4" (10.2cm) Long USA & Canada
Mayhew Steel Single Pin Punches 5/32" (4.0mm) 4" (10.2cm) Long USA & Canada

USD 9.99 (Indicative price - actual current price possibly lower)
No pin punch can be guaranteed against breakage, all the gunsmith can do is buy the very best available. When used with starting punches (see elsewhere), these will give you excellent service. Points will not bind in even deepest holes. Manufacturer: mayhew steel specs: tool steel. Knurled body. High specification gunsmith punches by Mayhew, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 587475156-587475062-11370.
More....

Mayhew Steel Mini Punches 1/16" Mini Punch USA & Canada
Mayhew Steel Mini Punches 1/16" Mini Punch USA & Canada

USD 10.99 (Indicative price - actual current price possibly lower)
These three small diameter punches give excellent control because of their short length. Ideal when doing small, precision work or in tight spots where a full length punch just won't fit. Forged, one-piece construction with knurled handle. Manufacturer: mayhew steel specs: 2 " (7cm) overall. " (19mm) punch section. Steel. High specification gunsmith punches by Mayhew, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 587474062-587474062-11370.
More....

Little Crow Gunworks Ar 15 Trigger Guard Roll Pin Pusher For Ar 15 Style Rifles USA & Canada
Little Crow Gunworks Ar 15 Trigger Guard Roll Pin Pusher For Ar 15 Style Rifles USA & Canada

USD 59.99 (Indicative price - actual current price possibly lower)
Pocket-sized tool helps prevent breaking the triggerguard tab or marring lower receiver finish when installing or removing the roll pin. Tool fully supports triggerguard tab while slowly pushing the roll pin in or out of its channel. Includes steel alignment pin and push pin to aid in roll pin removal and installation. Manufacturer: little crow gunworks, llc. Specs: aluminum body, anodized. Molded thermoplastic handle, 1-7/16" (3.6cm) diameter. Steel screw, push pin and alignment pin. High specification gunsmith punches by Little Crow, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 100011602-100011602-11370.
More....

Brownells Gunsmith Replaceable Pin Punch Set Replacement Pin Punch 2" Long .039 Dia. USA & Canada
Brownells Gunsmith Replaceable Pin Punch Set Replacement Pin Punch 2" Long .039 Dia. USA & Canada

USD 10.99 (Indicative price - actual current price possibly lower)
Finally! what we think is the answer to the pin punch headache that has plagued us - and every other gunsmith who has ever knocked out a gun pin, had the punch break or bend, and been out of business until a new one could be made or ordered. Now - just replace the tip!handles, with removable knurled-chuck to hold punch, are made of powerful, fatigueproof c.R.S. Steel - tensile strength of over 140,000 psi (min.). Replaceable punch - the secret of the tool. These are special, tool steel, bevel-headed punches designed for the tool, die and mold manufacturers as perforators, punches, ejectors and core pins. Oil hardened to rc 58-60. Heads are annealed to rc 42-45. They come in two lengths a Manufacturer: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins are 2" (5.1cm) or 2 " (6.3cm) long. Replacement pin punch sets include the following pin sizes: 0.039", 0.060", and 0.091" in either 2" or 2 " lengths. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080507239-080507239-11370.
More....

Brownells Dovetail Sight Punch Dovetail Punch Kit USA & Canada
Brownells Dovetail Sight Punch Dovetail Punch Kit USA & Canada

USD 21.99 (Indicative price - actual current price possibly lower)
These punches are specifically designed for the installation, removal, and adjustment of front and rear handgun sights. Made of brass so they will not mar the sight or the gun if you slip. Unique triangular punch faces and heavy-duty bodies make them indispensable working tools for the gunsmith. Can be re-ground to square up the flat after multiple uses. Front sight punch has a base width of approximately .280". Rear sight punch has a base width of approximately 0.480". They are sold separately or can be purchased together in a handy kit. The small dovetail sight punch (sold separately) has a .230" base width, making it ideal for front and rear sights on compact handguns. Manufacturer: brownells. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080001164-080001138-11370.
More....

Brownells Premium Roll Pin Punches Kit USA & Canada
Brownells Premium Roll Pin Punches Kit USA & Canada

USD 34.99 (Indicative price - actual current price possibly lower)
Hardened steel punches easily remove roll pins from firearms incorporating these pins. Balled tip helps locate the punch on the pin and protects pin end from damage during removal or installation. Available as a 7-punch set or sold individually, as listed below. Manufacturer: brownells specs: carbon steel, heat hardened. Set contains 1 each of 1⁄16",5⁄64", 3⁄32", 1⁄8", 5⁄32", 3⁄16", and 7⁄32" diameter punches. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080001083-080001083-11370.
More....

Brownells Starter Punch Set Replaceable Starter Punch .091 Dia. USA & Canada
Brownells Starter Punch Set Replaceable Starter Punch .091 Dia. USA & Canada

USD 9.99 (Indicative price - actual current price possibly lower)
We are constantly encouraging you to always use starting punches to break tight pins loose - then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip - or - break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! Manufacturer: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins. .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080513091-080513039-11370.
More....

Lyman Gunsmith Punch Set USA & Canada
Lyman Gunsmith Punch Set USA & Canada

USD 26.99 (Indicative price - actual current price possibly lower)
Quality steel punches with hardened steel punch tips and knurled steel handles. Set includes sizes 1/16, 3/32, 1/8, 5/32, and 3/16 in. Punches. 1/8 in center punch. Brass drift punch. Storage block. Works well in conjunction with the brass tapper above. Manufacturer: lyman. High specification gunsmith punches by Lyman, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 749003522-749003522-11370.
More....

Grace Roll Pin Punches 7 Punch Set USA & Canada
Grace Roll Pin Punches 7 Punch Set USA & Canada

USD 32.99 (Indicative price - actual current price possibly lower)
Hardened steel punches easily remove roll pins from firearms incorporating these pins. Balled tip helps locate the punch on the pin and protects pin end from damage during removal or installation. Available as a 7-punch set or sold individually, as listed below. Manufacturer: grace USA specs: carbon steel, heat hardened. Set contains 1 each of 1⁄16",5⁄64", 3⁄32", 1⁄8", 5⁄32", 3⁄16", and 7⁄32" diameter punches. High specification gunsmith punches by Grace, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 354000025-354000025-11370.
More....

Brownells Roll Pin Holders #4 1/8"(3.2mm) Dia 5"(12.7cm) O/A Length USA & Canada
Brownells Roll Pin Holders #4 1/8"(3.2mm) Dia 5"(12.7cm) O/A Length USA & Canada

USD 15.99 (Indicative price - actual current price possibly lower)
Holds roll pins perfectly aligned for starting correctly. Especially good on the tiny, tough-to-grab ones, or those in tight places. 1/16" is notched to clear m16/ar-15 rear sight. 3.5mm excellent for holding the pin that retains the breech block on sig handguns. Finish driving with roll pin punch. O/a in chart means "overall". Available individually or as a set of 5. Manufacturer: brownells specs: steel, knurled handle. Set of 5. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080685125-080685125-11370.
More....

Brownells Roll Pin Punches Kit USA & Canada
Brownells Roll Pin Punches Kit USA & Canada

USD 45.99 (Indicative price - actual current price possibly lower)
With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Manufacturer: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm). #2, 5/64" (2.0mm). #3, 3/32" (2.4mm). #4, 1/8" (3.2mm). #5, 5/32" (4.0mm). #6, 3/16" (4.8mm). #7, 7/32" (5.5mm). High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 230100000-230100000-11370.
More....

Brownells Alignment & Push Punches .120" Diameter Steel USA & Canada
Brownells Alignment & Push Punches .120" Diameter Steel USA & Canada

USD 8.99 (Indicative price - actual current price possibly lower)
For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste Manufacturer: brownells specs: handle - plastic. Shank - unhardened steel drill rod, or 360 alloy brass . 3 " (8.2cm) long. Oal - 4 " (12.1cm) long. Alignment/push punch set - contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080000030-080000029-11370.
More....

Grace Roll Pin Punches 7/32" Punch USA & Canada
Grace Roll Pin Punches 7/32" Punch USA & Canada

USD 8.99 (Indicative price - actual current price possibly lower)
Hardened steel punches easily remove roll pins from firearms incorporating these pins. Balled tip helps locate the punch on the pin and protects pin end from damage during removal or installation. Available as a 7-punch set or sold individually, as listed below. Manufacturer: grace USA specs: carbon steel, heat hardened. Set contains 1 each of 1⁄16",5⁄64", 3⁄32", 1⁄8", 5⁄32", 3⁄16", and 7⁄32" diameter punches. High specification gunsmith punches by Grace, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 354000032-354000025-11370.
More....

Brownells Gunsmith's Alignment Pins Large Alignment Pin USA & Canada
Brownells Gunsmith's Alignment Pins Large Alignment Pin USA & Canada

USD 10.99 (Indicative price - actual current price possibly lower)
Made for us exclusively, to our professional specifications, and are forged, taper-ground and polished. Dimensions set to give you size overlap from pin to pin to cover every conceivable situation. Tapers are 2" long on the 4" long pins. Manufacturer: brownells specs: taper as follows: small, from .070" (1.8mm) to .156" (4.0mm). Medium, from .110" (2.8mm) to .187" (4.7mm). Large, from .150" (3.8mm) to .219" (5.6mm). Knurled handle. Steel. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080645015-080645007-11370.
More....

Gauge Rite Products Top Dead Center Punch USA & Canada
Gauge Rite Products Top Dead Center Punch USA & Canada

USD 37.99 (Indicative price - actual current price possibly lower)
The tdc is a rugged, foolproof tool to end the problems of off-center-work, broken taps and drills that come about from trying to "eyeball" top dead center on gun barrels or other round stock. Simple to use - just level and plumb the rifle on the drill press, place tdc on barrel or receiver, level the bubble and tap the punch. The punch mark is top dead center. Precision made. Shockproof level. Manufacturer: gauge-rite products specs: body - 1-15/16" (23.8mm) x 1- " (3.8mm) x 1" (2.5cm), aluminum. Punch - " (6.3mm) diameter tool steel. Locating rod - 5- " (14cm) long. High specification gunsmith punches by Gauge-Rite, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 871100000-871100000-11370.
More....

Brownells Premium Roll Pin Starter Punches 3/16" Roll Pin Starter Punch USA & Canada
Brownells Premium Roll Pin Starter Punches 3/16" Roll Pin Starter Punch USA & Canada

USD 5.99 (Indicative price - actual current price possibly lower)
Hardened steel punches easily remove roll pins from firearms incorporating these pins. Balled tip helps locate the punch on the pin and protects pin end from damage during removal or installation. Available as a 7-punch set or sold individually, as listed below. Manufacturer: brownells specs: carbon steel, heat hardened. Set contains 1 each of 1⁄16",5⁄64", 3⁄32", 1⁄8", 5⁄32", 3⁄16", and 7⁄32" diameter punches. High specification gunsmith punches by Brownells, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 080001080-080001075-11370.
More....

Grace Ps 8 Grace Brass Punch Set USA & Canada
Grace Ps 8 Grace Brass Punch Set USA & Canada

USD 33.99 (Indicative price - actual current price possibly lower)
Punches are machined from solid brass hex stock with a flat head and extra-long shaft to drive pins completely out. Brass is softer than steel, so it won't gouge the gun if you slip. Standard flathead punches (excellent for drifting sights. Contains the following 8 sizes: 1⁄16", 3⁄32", 1⁄8", 5⁄32", 3⁄16", 7⁄32", ", 5⁄16" dia. All punches are 3 " long. Manufacturer: grace USA. High specification gunsmith punches by Grace, buy online with confidence at best discount price and fast shipping to U.S. and Canada. Manufacturer produt ID 749009236-749009236-11370.
More....











Try Search on this site - find exactly what you need!




Item on this page: Gunsmith Punches USA & Canada



Home Page Search Products Contact Us Privacy Policy



Copyright © StarGunSupply.com : 1997 - 2024 : All rights reserved. 140-FT